Limiting Signal Level to Test Equipment
How much attenuation is needed for my test equipment?
If you have a NanoVNA or a TinySA in your shack, one thing you must be careful of is the maximum amount of power these devices will take before releasing the magic smoke. Even static electricity can cause problems. Please don't ask me how I know this. The devices are not overly expensive nowadays, but having to replace them (or repair them) is still costly in dollars and time. You cannot imagine how small some of the components are in these devices.

To safely connect to your test device, you should know the max amount of power your device can accept, and then you should not present that amount to the device. Actually, for safety, you should present about half to 3/4 of the maximum power to the device.
As an example: My TinySA has a maximum power input of 6 dBm or 0.004 Watts. I want to limit the power to the TinySA to 2 milli-Watts (0.002 Watts) just to be safe.
You can calculate the amount of attenuation needed by using a formula, but many of us hate to see and use formulas. In any case here are the parameters:
Power In (Pin) = power in Watts going into the attenuator.
Power Out (Pout) = power in Watts coming out of the attenuator.
Attenuation (AdB) = attenuation needed to reach (Pout), which in this case is the limit I have set for my TinySA.
Here is the formula:
AdB = 10 * log10(Pin / Pout)
Let’s do an example with the values for my TinySA:
Pin = 10 Watts
Pout = 0.002 Watts
AdB = 10 log10(10 / 0.002)
= 10 log10(5000)
= 10 * 3.699
= 36.99 dB
This is the attenuation needed to reduce the power from 10 Watts to 2 milli-Watts. I would recommend using at least 37 db of attenuation or even 40 to be safe. Keep in mind the attenuator in this case must be able to handle 10 Watts.
Also note that you can stack attenuators (and add the values together) to reach non-standard values. No need to worry about fractions of a dB. Round up or down to a whole number attenuation value.
I created a Google Drive calculation spreadsheet with a couple tables for two different calculations. The spreadsheet is shareable, so others can access it and make entries and calculations to fit their situations.
The upper table allows you to calculate the attenuation needed to reduce the power of the radio to a level acceptable to the test device, either a Vector Network Analyzer or Spectrum Analyzer.
The Lower Table calculates the Power Out of the attenuator when the Power In to the attenuator and the Attenuation are known. Go to the link below and enter the Power In (Pin) and Power Out (Pout) into the appropriate cells and the attenuation required (AdB) will be calculated and displayed in the third cell. Only put values in the orange cells for Pin (W), Pout (W), & AdB (dB). Green cells are all calculated. Do not change values in the green cells, or the spreadsheet will no longer work correctly. The green and orange cells containing “Inputs” and “Calculated” are just to remind the user that the colored cells either need user input (Orange), or the values are calculated (Green).
To go to the tables, click this Link to Calculation Tables As a check to see if tables are correct and accurate:
In the Upper table, input 10 into the Pin cell and 0.002 in the Pout cell. This should result in a value of 36.99 in the AdB cell. In the area just below the Upper table is a summary of the calculation.
In the Lower table, input 10 into the Pin cell and 36.99 in the AdB cell. This should result in a value of 0.002 in the Pout cell. In the area just below the Lower table is a summary of the calculation.
If you get the values specified just above, the calculations are correct. If you get other values or errors, notify Bill Powell, w9wrp@yahoo.com to let him know the spreadsheet is possibly corrupted.
There may be a situation where you know the the radio’s Power In (Pin) in Watts and the Attenuation (AdB) value in dB, and you want to know what the the resulting Power Out (Pout) in Watts would be.
The Lower table in the spreadsheet found at the link above can be used to calculate the value. Go to the link above and, in the Lower Table, enter the Power In (Pin) and the Attenuation (AdB) values. The resulting (Pout) will be calculated and displayed in the third cell. Note that Pin is the Power in Watts going into the attenuator. In some cases this may be the output power of the radio itself. Also note that Pout is the Power in Watts coming out of the attenuator.

Hope this makes it clearer how to determine the value of an attenuator needed to keep your test equipment safe.





Comments